Design Engineering

mackanzee engineering Company with the best qualified engineering group handled various cement,mining,oil, gas,  and power plant projects(cogen,threcogen wind and sun power plant). Consultancy, feasibility studies, basic and detail designs, engineering and preparation of all required specification for material procurement, manufacturing and construction with the well known consultancy and reputable domestic and foreign consultant engineering companies. Evaluation and selection of suppliers and manufacturers, technical and commercial evaluation of proposals have been Delham staff activities for many years.

Process Design

  Company has good experiences in wide spectrum of research and Process Design in steel, oil & gas industry. By a team of Engineers and Specialists, originating from Engineering Companies, who have acquired experience in different type of process design in oil & gas Industry, Power Station, etc.  As a principal engineering group for Process Design and Loss Prevention in International Engineering, Procurement and Construction (EPCM) Company, We have involved in power plants & refinery plants EPCM projects. Delham Engineering Company is well conversant in International Code and Standards NFPA, API, IP, OCIMF and Standards for Global Insurances players likes UL, FM & GSPA. 

 

Mackanzee engineering group is supported with the latest developed software for PROCESS SIMULATION as follows:

Software             Used for

Aspen HYSYS®  Optimize process design & operations in oil & gas producers, refineries and engineering company

Aspen Plus®      Design & Improve process plants in chemical organization and related industries

Aspen Exchanger Design & Rating (EDR)              Exchanger Design and Rating

HTRI      Design, rating, and simulation of air-cooled heat exchangers, heat recovery bundles, and air preheaters, fired heaters

EES(Engineering Education Solver)         High accuracy thermodynamic and transport functions for 100's of fluids

Fluent   Fluid analysis software

COSMOS Floworks         Fluid flow simulation and thermal analysis program that is fully embedded inside SolidWorks

Flaresim              Modeling of thermal radiation and noise footprints generated by flare systems for offshore platforms, gas plants, refineries and chemical plants, and predicts the temperature of exposed surfaces within range

Thermo flow     Gas turbine-based cycles, pure steam power plants, and repowering existing steam plants by adding gas turbines.  It also used for the Plant Design Expert (PDE)

 

  Mackanzee engineering  engineering group is supported with the latest developed software for mechanical design as follows:

                                Software                      Used for

Pv-Elite PV-Elite is used to design, bid or re-rate a wide variety of vessels and vessel components in accordance with ASME Code Section VIII Division 1, Division 2, Canadian NBC, EN-13445 and PD5500 rules.

Nozzle Pro          Nozzle Pro is a powerful FEA tool that combines the most frequently used FE/Pipe templates with an extremely simple user-interface. (The templates, specifically, are nozzles and structural attachments that intersect with heads, cylinders and cones).

Tank      Intergraph TANK is a comprehensive, easy-to-use software package for the design, analysis and evaluation of oil storage tanks. It provides users with quick and accurate designs for new tanks and evaluation of existing tanks.

Ansys    ANSYS Mechanical software offers a comprehensive product solution for structural linear or nonlinear and dynamics analysis. The product provides a complete set of elements behavior, material models and equation solvers for a wide range of engineering problems.

Ceasar II              CAESAR II was the first pipe stress program specifically designed for the PC environment. CAESAR II incorporates a wide range of capabilities, from numerous piping codes, to expansion joint, valve & flange and structural data bases, to structural and buried pipe modeling, to equipment and vessel nozzle evaluation, to spectrum and time history analysis.

Auto Pipe           AutoPIPE is a native Windows program for calculation of piping code stresses, loads, and deflections under static and dynamic loading conditions. AutoPIPE is designed to analyse systems of any complexity; with special features for buried pipeline analysis, wave loading, fluid transients, FRP/GRP pipe, and pipe / structure interaction.

CAEPipe              CAEPIPE, the first pipe stress analysis software on PC, continues to be the preferred tool for static and dynamic stress analysis of piping systems of any complexity in any industry.

By using CAEPIPE early in the design process of a piping system, pipe system designers will find the critical areas early in the design process.

SAP2000              The SAP name has been synonymous with state-of-the-art analytical methods since its introduction over 30 years ago. From a simple small 2D static frame analysis to a large complex 3D nonlinear dynamic analysis, SAP2000 is the answer to all structural analysis and design needs.

ETABS 2000        For nearly 30 years, ETABS has been recognized as the industry standard for Building Analysis and Design Software. Today, continuing in the same tradition, ETABS has evolved into a completely Integrated Building Analysis and Design Environment. Integrated analysis, design and drafting of building systems.

Weld spec.         TWI's Weldspec Plus has been used for many years to manage welding procedures. Weldspec is designed to manage WPS,WPAR/PQRs and Welding data collection sheets (PQRDs). The format of the screens which are used for data entry and viewing, and the hardcopy printouts, are based on the layout recommended by the most commonly used codes, including EN 288, ASME IX and ASME IX.

Microsoft Word               Microsoft Word is a word processor and was previously considered the main program in Office. Word is used for Scripts and other writing pieces. Also it is used for preparation of documents which is reported to client.

Microsoft Excel Microsoft Excel is a spreadsheet program. It is used for preparation of documents which is reported to client.

 

Design Engineering

Mackenzee Engineering Company is an owner-operated company with years of experience in computer-aided drafting. Providing unique designs and working drawings for all equipment of oil & gas industries. Designing, drafting, or transferring board drawings to computer, all are performed to related standards and specifications. Client satisfaction is our top priority.

 

Mackenzee engineering group is supported with the latest developed software for drawing preparation as follows:

 

Software             Used for

AutoCAD             2D and 3D CAD design

Mechanical Desktop      2D and 3D CAD design

SolidWorks (3D CAD Packages) powerful 3D design solution for rapid creation of parts, assemblies, and 2D drawings

PDMS   PDMS as it is known in the 3D CAD industry, is a customizable, multi-user and multi-discipline, engineer controlled design software package for engineering, design and construction projects. PDMS includes comprehensive functions for all aspects of 3D plant design.

Contact Us